ANSI C82.1-1985 R1992
|
ID： |
AD91B62BB08F417A9F755B5F53FAAC63 |
|
文件大小(MB)： |
1.13 |
|
页数： |
21 |
|
文件格式： |
|
|
日期： |
2007-12-7 |
|
购买： |
文本摘录（文本识别可能有误，但文件阅览显示及打印正常，pdf文件可进行文字搜索定位）：
I NOTICE OF I,I ADOPTION I,ANSI C82.1-1985 was adopted on 23 December 195,Department of Defense (DoD).' The American Nat,furnished the clearance required by existing x,document are stocked at the Standardization Dc,700 Robbins Avenue, Philadelphia, PA 19111-5C,only. All other requestors must obtain copies,ANS I,11 W. 42nd Street,New York, NY 10036,Title of Document: Standard for Ballasts for,Date of Specific Issue Adopted: May 17, 1985,C82.la-1990 (,C82.lb-1990 (,C82.l~-1990 (,Releasing Non-Government Standards Body: ANSI,Custodian:,Navy - YD,DISTRIBUTION STATEMENT A.,unlimited.,Approved for public,ADOPTION NOTICE 2,23 December 1991: for,ANSI C82.1-1985 i,May 17, 1985* ! I,and is approved for use by the,mal Standards Institute has ',plations. Copies of the,unents Order Desk, Bldg. 4D, I,c , for issue to DoD activitieis,Irom:,I,i,Luorescent ~amps - Specifications,kincluding Supplements,inuary 22, 1990),5bruary 21, 1990), and,inuary 22, 1990) I 1,Military Coordinating Activity:,Navy - YD,(Project 6240- 1303),I,I,FSC 6246,dease; distribution is i,A N S I C82-L 85 072LiL.50 0032022 5 M,Lamp type,ANSI C82.1 a-1 991,Revision of ANSI C82.la -1990,Supplement to ANSI C82.1-1985,Minimum light output,tolerances (percent),American National Standard 7,for ballasts for fluorescent lamps -,specif ?cat ions,(replacement for table 6),( Approved July 15, 1991 Secretariat: National Electrical Manufacturers Association ),This table replaces table 6 in ANSI C82.1-1985, and revises ANSI C82.1a-1990,Linear lamps,4,6,8WT5,14WT8,15WT8,14, 15,20WT12,17, 25,32,40WT8,30,40WT12,'34WT12,0.800A and 1 .OA Ti 2,1.5A T12 and PG17,Circular lamps,20WT9,22,32,40WT9,32WT10,40WT1 O,U-Shaped lamps,16, 24,31WT8,40WT12,-10,-1 o,-1 o,-1 o,-7.5,-7.5,-1 5,-5,-5,-1 O,-10,-10,-10,-7.5,-7.5,'A ballast that is rated for use with both a 40-watt and a 34-watt lamp and,meets the 40-watt lamp requirements need not be testedon a34-watt lamp.,____ ~~,An American National Standard implies a consensus of those substantially concerned with its scope and provisions. An American,National Standard is intended as a guide to aid the manufacturer, the consumer, and the general public. The existence of an,American National Standard does not in any respect preclude anyone, whether he has approved the standard or not, from manufacturing,marketing, purchasing, or using products, processes, or procedures not conforming to the standard. American National,Standards are subject to periodic review and users are cautioned to obtain the latest editions.,The American National Standards Institute does not develop standards and will in no circumstances give an interpretation of any,American National Standard. Moreover, no person shall have the right or authority to issue an interpretation of an American National,Standard in the name of the American National Standards Institute.,CAUTION NOTICE: This American National Standard may be revised or withdrawn at any time. The procedures of the American,National Standards Institute require that action be taken to reaffirm, revise, or withdraw this standard no later than five years from the,date of approval. Purchasers of American National Standards may receive current information on all standards by calling or writing,the American National Standards Institute.,I \,Copyright O 1991 by American National Standards Institute, 11 West 42nd Street, New York, N.Y. 10036 ANS14Ci191110 '- i,--`,,,``,,``,,,`,,,``,,`,,`-`-`,,`,,`,`,,`---,ANSI C82-3 85 0724350 0032023 7,Voltage across,dummy load,(vo It s ),ANSI C82.1 b-1991,Revision of ANSI C82.lb-1990,Supplement to ANSI C82.1-1985,Voltage,during,operations,(volts),American National Standard,for ballasts for fluorescent lamps -,specifications -,(replacement for table 7),Approved July 15, 1991 Secretariat: National Electrical Manufacturers Association,Page 1 of 2 pages,This table replaces table 7A in ANSI C82.1 b-1990. (Table 7B is not revised.),Table 7A - Cathode voltage limits for rapid start lamps,~,Lamp type,Linear lamps,17,25,32,40WT8,30,34,40WT12,40WT1 O,0.800A and 1 .OA TI 2,1.5A T12 and PG17,Circular Lamps,20WT9,22,32,40WT9,32,40WT10,U-Shaped Lamps,16,24,31WT8,40WT12,Dummy,load *,(ohms),11 .o fO.1,9.6f0.1,9.6 f 0.1,3.2 f 0.05,3.2 f 0.05,9.6 f 0.1,9.6 f 0.1,9.6 f 0.1,1 1 .o f 0.1,9.6 f 0.1,I,4.4,4.0,4.0,4.0t,4.3,4.0,4.0,4.0,4.4,4.0,Where one ballast winding operates two cathodes in parallel, the dummy load resistor should be half the value,given.,t Maximum voltage is 4.3V if the filament resistance exceeds 150% of the stated objective. See ANSI C82.2-,1984 for method of measurement.,An American National Standard implies a consensus of those substantially concerned……
……